automatic motor winding machine

Automatic Electric Motor Testing Equipment For Inductive Motors / Pump This tester is applied to integrated test varieties of compressor stator in refrigerator, air conditioner and heater etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stators. Do auto compensation to ambient temperature. 2 working stations Systems switch device is made of imported high pressure vacuum steel spring relay Flash

Auto Double Sides Motor Stator Coil Winding Machine ISO / SGS Audit Safety, quality and efficiency are the cornerstones of our lacing machine. The end turns are laced with a "diamond" stitch pattern. Both sides are laced at the same time and a real knot is being tied at the end. It is equipped with two needles, each needle for laing each side of stator coils. The needle movement is controlled by servo drive system to complete the lacing work. There are no dangerous manual

Three - Phase Motor Stator End Motor Winding Equipment SMT - DB100 This lacing manchine is especially applied to multi sizes, low output or more lead stator winding lacing. This machine is suitable for stator used in induction motor industry, such as pump motor, fan motor, and washing machine motor. (1) Main Technical Information Model DB100 Stack Height 10-100mm Stator I.D. 35-120mm Stator O.D. ≤160mm Height of coil ≤40mm Lacing Mode Slot by slot/interval slot/Fancy lacing

Slot AutomaticWinding Inserting Machine for Fan / Washing Machine / Pump Motor 1. Easy to operate. 2. Need cut the required wire length before winding. 3. Easy to switch the winding fixture for different size core. 4. Operation with compressed air. 5. Spread wire by manual. (1) Main Technical Features Model SMT-QX10 Stator I.D 110-210mm Stator O.D ≤260mm Core Length ≤250mm Tooling stroke ≤90mm Compatible wire CU/AL Slot number range 24-48 slots Power supply 380V/50/60Hz 6.5Kw

Motor Servo Double Side Coil Lacing Machine Motor Production Machine SMT - DB190 Each lacing machine is PLC controlled with an inverter drive and can be fully programmed to suit different stator slot configurations. Stator support tooling is very quick to changeover between different stator laminations and stack heights. A wide range of standard lacing needles are available. This lacing machine is suitable for lacing multi-species, less yield or more lead wire stator. This

Four Working Station Automatic Stator Winding and Coil Inserting Machine (1) Main Technical Features 1# Main Features: 1. Suitable for different frame sizes big motor stator with case or without case; 2. Adopting servo motor to control the inserting speed; 3. Working table and stator fixing shelf are easy to be rotated; 4. Machine can be operated by one operator, which improves the production efficiency. 2# Range: SMT-QL80 for frame size: 180~250 SMT-QL140 for frame size: 280

Induction Motor Stator Coil Horizontal Single Side Lacing Machine SMT-DW300 This machine is used to bind the engine stator coil, applicable for various wires binding methods, and equipped with tension controller to adjust the tightness degree of binding wires. (1) Main Technical Information Model DW300 Stack height 100 - 260mm Stator I.D 110-210mm Stator O.D ≤ 301mm Height of Overhang ≤50mm Laccing mode Slot by slot / interval slot/Fancy lacing Lacing speed 8-48 slot Power

Motor Servo Double Side Coil Lacing Machine Motor Production Machine Description: Double ends electric motor stator coil automatic lacing and binding machine . This Automatic motor stator coil lacing machine is consist of machine body, needle, nozzle rotating part, needle fore and back movement,nozzle swing part, needle up and down movement part, stator indexing part,thread feeding,thread cutting part. This stator coil lacing machine adopts servo driven system, CNC control

Winding Inserting Machine Electrical Motor / Permanent Magnet Motor Based on your production needs. 1. Design the suitable product or production line for you ,OEM and ODM available. 2. We have professional and rich experience engineers in the domestic and overseas. 3. We will wind and test the samples in our plant before delivery. (1) Main Technical Features Model SMT-QX10 Stator I.D 110-210mm Stator O.D ≤260mm Core Length ≤250mm Tooling stroke ≤90mm Compatible wire CU/AL